ALS

AUTO LIGHT STARTER

Automatically turning on the lights of the vehicle when the engine is started

scroll for more

What is ALS?

an automate for turning on the lights

ALS is an electronic device which purpose is to automatically turn on the lights of the vehicle after the engine is started. It is designed so that it could be connected to every 12V vehicle system! It can be also connected to 24V (24V power supply with two consecutively connected 12V batteries).

  • Overload protection of the output
  • Small own consumption
  • Moisture resistant and dustproof
  • Small size

ALS is an electronic device which purpose is to automatically turn on the lights of the vehicle after the engine is started. ALS monitors the voltage of the vehicle electric system and when it reaches 13.2V, it turns on the lights with a 5÷6 sec delay. After the engine stops, the lights go off with a 5÷6 sec delay after the voltage drops below 13.1V. The timespan for turning them on and off depends on the battery condition and the electric system of the vehicle!

If the electrical system of the vehicle does not work properly, ALS will also not work properly!

ALS is designed so that it could be connected to every 12V vehicle system! It can be also connected to 24V (24V power supply with two consecutively connected 12V batteries). The power supply of the ALS shall be directly connected to one of the batteries, the other inputs shall be connected through the matching units. (See exemplary connection schemes). ALS operates a 12V/133 mA relay (not included in the set). The low beams of some vehicles are turned on via the relays which can be used when connecting the ALS to the electric system of the vehicle. Relays with other technical parameters can also be used. They shall have at least 15A current in the sockets and no more than 300mA current in the control coil. In case of overload of the output, ALS goes in emergency mode and disconnects its output. In order to bring back ALS to its normal working mode, you should turn off the engine of the vehicle and the lights switch (if connected to the ALS). You should eliminate the overload cause! If ALS has been directly connected to the battery of the vehicle, you should wait for the voltage of the battery to drop below the turn off voltage. When the engine is started again or when the lights switch is connected (if connected to the ALS), the device will work properly.

Size and outputs

  • 1 - black - Power input minus
  • 2 - red - Power input plus
  • 3 - yellow - Relay output plus
  • 4 - gray - Relay output minus
  • 5 - green - Low beams input
  • 6 - green - Low beams input
  • 7 - blue - High beams input
  • 8 - blue - High beams input
  • 9 - white - Front fog lights input
  • 10 - white - Front fog lights input

Technical parameters

  • Working voltage:
    10V ÷ 16V
  • Maximum output consumption:
    300mA
  • Standby mode consumption 12V:
    1,02mA
  • Working temperature:
    -30 °C ÷ +60 °C
  • Protection marking:
    IP 67
  • Dimensions:
    60.7 x 40.5 x 6.2mm
  • Length of the connecting conductors:
    180mm
  • Weight:
    36g
Contact form

Terms of order

  • The shipment costs when ordering a product are at the expense of the buyer.

  • In the event COD (cash on delivery) is used as payment method, the buyer has the right to inspect the condition and the packaging of the product before paying for it.

  • The buyer has the right to return a product purchased from a distance within 14 days after receiving it. The amount paid for the product will be returned after the seller receives the product back. In case the product is not sent COD, the seller will contact the buyer to arrange for the return of the amount paid for the product.

  • The product has to be returned as it was: without damages, fully packaged and with all accompanying documents.

  • When returning a product sent COD, the seller inspects the condition and the packaging of the product before paying the amount for the goods.

  • The shipment costs for the return are at the expense of the buyer.

  • A form for right of withdrawal

Packaging

  1. ALS – 1 pc;

  2. Installation and usage instruction – 1 pc;

  3. Warranty card / declaration of compliance – 1 pc;